Skip to content
ANDANTEX / PRECISION TRANSMISSIONSelection Support / 3D Resources / Custom Engineering

Servo Motor Interface Dimensions: Gearbox Matching Checklist

Check servo motor shaft diameter, usable length, pilot, mounting holes and input connection against the gearbox drawing before ordering.

Quick answer: Before matching a servo motor to a gearbox, compare shaft diameter and usable shaft length, shaft profile, locating pilot, mounting-hole pattern, flange clearance and input connection. Use the drawings for the exact motor and gearbox configuration; motor power alone does not establish compatibility.

Servo Motor Interface Dimensions: What to Check

A motor can have the required power yet still need a different gearbox input adapter. Start with the complete motor model and its mechanical drawing, then compare the following items with the proposed gearbox input drawing.

Item Information to compare Why it matters
Shaft diameter Diameter and specified tolerance at the connection area. The shaft must match the selected coupling or input bore.
Usable shaft length Projection from the mounting face, usable engagement length and available input depth. A long shaft may bottom out; a short shaft may provide insufficient engagement.
Shaft profile Plain shaft, key and keyway dimensions, spline specification or other shaft features. The input connection must accept the actual shaft geometry.
Locating pilot Pilot diameter, projection or recess depth, and specified fit. The locating features must fit together to support alignment.
Mounting holes Hole count, pitch-circle diameter or center distances, hole orientation, and thread or clearance-hole specification. A similar flange outline does not guarantee that the fasteners align.
Flange and installation clearance Flange dimensions and thickness, shoulder clearance, fastener access and surrounding installation space. The mounting faces must seat correctly and the connection must remain accessible for assembly.

Motor-to-Gearbox Interface Comparison Worksheet

Copy this blank checklist into your enquiry and enter values only from the exact motor and gearbox drawings. Record units, tolerances and drawing references. Empty cells mean the information still needs to be supplied; this worksheet is not a compatibility approval.

Motor model and drawing reference: __________
Gearbox model, ratio, stage and drawing reference: __________
Input connection form: __________

Check item Motor drawing value Gearbox drawing value Item to confirm
Shaft diameter and tolerance __________ __________ __________
Shaft projection, usable length and input depth __________ __________ __________
Shaft profile, keyway or spline; connection form __________ __________ __________
Locating pilot diameter, depth and fit __________ __________ __________
Mounting-hole count, spacing, orientation and threads __________ __________ __________
Flange thickness, outline and assembly clearance __________ __________ __________

Use Motor Interface Matching to narrow the options, then send the completed checklist and both drawings for confirmation. Do not infer a match from motor power or flange size alone.

Confirm the Input Connection Before Checking the Fit

For the ANDANTEX configurations discussed here, coupling-bore input means an input bore equipped with a coupling to match the servo motor shaft. Splined-bore input, keyed-bore input and shaft input are other connection forms. These terms describe different interfaces and should not be treated as interchangeable.

Read what bore input means and how the four gearbox input forms differ before specifying the connection. Do not assume that a key should be removed, a shaft should be modified or a particular clamping method applies. Confirm the required arrangement against the applicable drawing and assembly instructions.

Does the Same Motor Power Mean the Same Interface?

No. A power rating such as 750 W does not identify shaft diameter, shaft length, pilot size or mounting-hole pattern. Check the complete motor model, including its variant, even when replacing a motor with another of the same rated power.

Mechanical fit is also only one part of selection. Check the required ratio, output speed, torque, load inertia and acceleration/deceleration cycle together. The servo motor planetary gearbox selection guide explains how to connect these requirements to series selection.

What to Send for an Interface Check

  1. The complete motor manufacturer and model designation, plus a readable mechanical drawing with units and tolerances.
  2. The proposed gearbox series, model, ratio and input connection, or the application requirements if a model has not yet been chosen.
  3. The shaft, pilot and mounting-hole dimensions listed above, with any keyway or spline details.
  4. The installation arrangement and available space, including any access restrictions.

To compare mounting arrangements before selecting a model, review the standard planetary gearbox series and interface selection checklist.

Ask for confirmation of the matched motor-to-gearbox interface before ordering. Fastener specifications, tightening torque and assembly clearances should come from the applicable confirmed drawings and instructions.

Send your motor drawing and gearbox requirements for a compatibility check.

Related FAQ

Do all 750 W motors have the same mounting interface?

No. Motor interfaces can differ between brands and between series from the same brand. Compare the actual drawings.

Read the related article
ENGINEERING SUPPORT

Need Help Applying This Information?

Send your application, motor details or drawing. The enquiry automatically records this article as its source.

Ask an EngineerBrowse Related Products2D / 3D Resources [STEP / PDF]
TECHNICAL DISCUSSION

Technical Questions & Discussion

Ask a technical question about this article. Names and questions may be published after review; email addresses are never displayed.

No published questions yet. Be the first to ask.

Leave a Technical Question

Required fields are marked *. Questions are reviewed before publication when comments are enabled.

ANDANTEX Product search

Catalogue guide · Beta
Guided catalogue search by model code — not AI chat. Searches are not stored.